UPDATE
参加的申请方法 （包括三天的听讲、论文集、座谈会等）
1.申请
请在“日本压铸会议申请书”上填写之后，支付费用的同时，用传真向协会申请。收到费用后受理申请。
2.截止日期
2022年10月14日（星期五）
3.会议的参加费用（包括三天的听讲、论文集、座谈会）
| 协会会员、高中・专科・大学教员： | 通常价格 42,350日元 | 早期优惠价格 31,900日元 |
|---|---|---|
| 一般： | 通常价格 84,150日元 | 早期优惠价格 63,250日元 |
|
高中・专科・大学学生： （限于没有职业的人） |
从此次开始免费了。 ※论文集收费。其价格还未决定。 |
|
※上述价格是含税价格。
※早期优惠适用于2022年9月14日（星期三）之前的申请。
※如希望使用银行汇款方式，请将费用汇至下列账号。汇款手续费请由申请人负担。
| 指定银行 |
①三井住友银行 日比谷支店 普通 7806186 ②三菱东京UFJ银行 虎之门支店 普通 2717730 |
|---|---|
| 账户名称 |
一般社団法人 日本ダイカスト協会 シャ）ニホンダイカストキョウカイ |
4.注意事项
• 会议期间听讲者可自由更换, 但仅限于同一单位的人员。
• 会议参加者可免费参加联欢会(10日)。
• 会议入场证在收到汇款以后发送(预定在10月下旬)。当天请勿忘记携带。
• 未带会议入场证者不能入场。
• 如在报名截止日以后取消参加计划, 恕不退还报名费, 但会议结束后将给您发送论文集。
※ 高中・高专・大学的学生(限于没有职业的人。不包括公司职员。)必须事前注册。请从主页下载注册 表后申请。
日本压铸会议
1. SPECIAL LECTURE
Future trends in the automobile industry and the impact on the die casting industry
* Auditing free,No pre-registration required
11/10 (Thursday)
• Special lecture 1
Presentation of scenario concerning reduction of consuming fossil fuel / energy for automobile and spread of electric vehicle
PhD Fujimura Toshio Visiting Professor, Faculty of Engineering, Aichi Institute of Technology, and Several corporate advisors
• Special lecture 2
Presentation of scenario concerning reduction of consuming fossil fuel / energy for automobile and spread of electric vehicle
PhD Fujimura Toshio Visiting Professor, Faculty of Engineering, Aichi Institute of Technology, and Several corporate advisors
详细信息和申请方法，请参照这里。
2. TECHNICAL PAPER PRESENTATION
※ Auditing charge
11/10 (Thursday)
JD22-01 Effect of various surface treatments on the soldering and erosion behavior in molten aluminum alloy
JD22-02 Effects of PVD coating, lubricant and shot peening on die casting dies
JD22-03 Erosion Resistance of Cast Steel and Spheroidal Graphite Cast Iron Containing High Manganese in Molten Aluminum Alloys
JD22-04 The evaluation of Ti matrix composite shot sleeve for the development
JD22-05 Die Casting Die Problems and Their Countermeasures
JD22-06 Development of high thermal conductivity die steel-based powder for 3D printing
JD22-07 Achieving High-quality Aluminum Die Casting via Cooling Control with Additively Manufactured 3D Cooling Dies and Preventing Corrosion of Cooling Channels
17:30-19:00 RECEPTION RISTORANTE ATTIMO (2F SEASIDE)
详细信息和申请方法，请参照这里。
11/11 (Friday)
JD22-08 Benefits on casting brought on the dies made of high thermal conductivity steel.
JD22-09 Prediction of Burr of Die-casting Molds
JD22-10 Evaluation of Flash-Boiling Atomization of liquid aluminum alloy containing air bubbles on die-cast process in fluid discharge.
JD22-11 Wave Behavior and Tilting Speed of Ladle Pouring in Die Casting
JD22-12 Development of new form minimum quantity spray type lubricant
JD22-13 The material properties evaluation for aluminum die-casting alloys
JD22-14 Alloy Solidification Morphology and Quality Characteristic of Die Casting
JD22-15 Research Trends of Non-Heat Treatment Al-Mg Alloy Die Casting for Automobile Body Parts and Activities of Aluminum Alloys Committee
JD22-16 Improvement of the modified effects in aluminum die castings by beat vibration method
JD22-17 Lowering Solutionizing Temperature and Shortening T6 Treatment Time for Al-Si-Mn-Mg-Cr-Cu Alloy Plate Fabricated by High Vacuum Die Casting.
JD22-18 Technical innovation by the measurement in the cavity and the artificial intelligence for the realization of the smart factory
详细信息和申请方法，请参照这里。
11/12 (Saturday)
JD22-19 Development and practical examples of "New die casting method" that solves blow holes and shrinkage porosities at the same time.
JD22-20 Development of electro-hydraulic actuator for die casting dies
JD22-21 Verification of production method for environmentally conscious die casting technology
JD22-22 Runner Squeeze Development
JD22-23 Development of Laser Heat Treatment Technology for SPR Joining of Aluminium Alloy Die Casting to Reduce CO2 to 1/10
JD22-24 Development of aluminum body parts manufacturing technology that requires T7 heat treatment
JD22-25 Die casting technologies of large body and chassis parts for automobiles
JD22-26 Effects of high response injection die-casting machines on product quality
JD22-27 Global development of the die-casting technology for the aluminum subframe
详细信息和申请方法，请参照这里。
3. 发表现场改善事例
※ Auditing charge
11/12 (Saturday)
JDK22-01 Initiatives for Preventive maintenance of Die Casting Machine
JDK22-02 Scrap Reduction Initiative Utilizing Thermal Imaging of Die Temperature
JDK22-03 Diecast plant paperwork switched digitalize for improvement QC and the work efficiency
JDK22-04 Reduction of frame line defect rate
JDK22-05 Structure that completely prevents water leakage from the mold cooling circuit
JDK22-06 Conditions of Cooling Water optimized to Environmental Changes and Efforts to Minimize the Quantity of Applying Mold Release Agent.
JDK22-07 Eradication of poor release agent supply to die casting lines